- Solidcam 2013 system requirements manual#
- Solidcam 2013 system requirements full#
- Solidcam 2013 system requirements verification#
When the stock is a casting (5% to 10% of parts) we need to define the home again for each new piece, because the casting stock is never exact. However in some cases the stock has let’s say a hole in the middle and the home has to be set always at the center of this hole – in that case maybe then we have to find the correction to the home with the probe every time. Home definition for 2nd Stock onwards When we put the stock of 2nd piece, we can push it against the stopper and hold it in the vice – this would be generally enough and there is no need to measure the home again (it is accurate enough). Visualization of the probe tool movements in the simulation prevents collisions and damage to the probe on the machineġ6 different cycles of the Solid Probe are available for home definition (Each such cycle can be used only if there is support for it in the controller probe cycles)
Solidcam 2013 system requirements manual#
Programming Home definition by Solid Probe is faster than manual programming on controller It is faster and safer to define the home by the Solid Probe module: This is not the case if operator is using controller for the first time or if he has no deep machining expertise. Setup (Home definition) for first piece of Stock, without Solid Probe, is done by using a cycle directly on the controller, if you know the controller well. Home definition Solid Probe provides an easy solution for home setting, using 16 different cycles, enabling the user to easily define home positions, replacing manual setup procedures. Visualization of all the Probe tool movements User-defined parameters give powerful flexibility for Probe cycles programming Solid Probe is a must tool for every machinist using Probes:
Solidcam 2013 system requirements full#
Solid Probe module provides also Tool Presetter support Full visualization of all the probe movements provided by SolidCAM Machine Simulation enables you to avoid any potential damage to the Probe tool.
Solidcam 2013 system requirements verification#
Welcome to the SolidCAM Solid Probe! SolidCAM is bringing you Solid Probe, a new SolidCAM module that provides capabilities for Home definition and On-Machine Verification (OMV), using probes on the CNC machine, to do setup and control the quality of machined parts. ExercisesĮxercise #1: Home Position.54 Exercise #2: Single Point Measurement.57 Exercise #3: Angle Measurement.60 Exercise #4: Boss/Pocket Measurement.63 Exercise #5: Cylinder/Hole Measurement.66 Exercise #6: Corner Measurement.69 Exercise #7: Multiple Holes Measurement.74 Measurement ResultsĪnalyzing Measurement Results.46 9. MiscellaneousĦ.1 Message.36 6.2 Extra parameters.36 6.3 Collision check.37ħ.1 Controller Probe Cycles.40 7.2 Renishaw Inspection Plus Software.41 7.3 Post processors.42 8. Technologiesĥ.1 Managing Technological cycles.24 5.2 Defining Technological cycles.25 5.2.1 Single Point cycles.27 5.2.2 Angle Cycles.28 5.2.3 Pocket/Boss Cycles.29 5.2.4 Hole/Cylinder Cycles.30 5.2.5 Arc Cycles.31 5.2.6 Corner Cycles.32 6. LevelsĤ.1 Start Level.22 4.2 Clearance Level.22 5. Toolģ.1 Tool tab.16 3.2 Data tab.19 3.3 Tool Change Position tab.19 4. SolidCAM User Guide: Solid Probe iMachining 2D & 3D | 2.5D Milling | HSS | HSM | Indexial Multi-Sided | Simultaneous 5-Axis | Turning & Mill-Turn | Solid Probeġ.1 Adding a Probe Operation.7 1.2 Probe Operation dialog box.8 2. SolidCAM + SolidWorks The complete integrated Manufacturing Solution